Metal Components for Industrial Equipment
Balford manufactures stamped and deep-drawn components for industrial equipment — valve housings, ferrules, anti-vibration bushings, brackets, lock plates and shims in steel, stainless, spring steel and aluminum. Production follows ISO 9001:2015 with IATF 16949-aligned quality controls on a 12,000 m² facility with 500+ machines.
What We Manufacture
Valve & Flow-Control Parts
Deep-drawn and stamped housings, ferrules and sleeves for hydraulic and pneumatic assemblies.
Anti-Vibration Bushings & Rings
Stamped metal bushings and rings for rubber-bonded collars in industrial mounts.
Brackets, Lock Plates & Shims
Structural brackets, nut lock plates and hardened adjusting shims for machinery.
Mounting Plates & Enclosures
Flat stamped plates and drawn enclosures for control and monitoring equipment.
Why Balford for Industrial Equipment Components
- Built for repeated mechanical load. Housings, brackets, ferrules and bushings are stamped and drawn so that fatigue-relevant geometry, radii and edges stay consistent batch to batch.
- Material range for the machine builder. Carbon steel for strength, stainless steel for corrosion, spring steel for shims and fasteners, aluminum for weight — with certificates on request.
- ISO 9001:2015 with IATF 16949-aligned quality management, with PPAP-aligned documentation, FAI reports and material certifications available on request.
- Prototype to production in one shop. We tool prototypes quickly, then move to production tooling sized for your annual volume — brackets, ferrules and housings included.
Featured Case Studies
Selected industrial equipment projects from Balford’s production history. Material, process and application data come from each case record.
Manufacturing Capabilities by Part Type
| Part Type | Typical Process Route | Key Requirements |
|---|---|---|
| Valve housings & ferrules | Deep drawing / stamping → plating | Bore consistency, crimp geometry, corrosion protection |
| Anti-vibration bushings / rings | Stamping, forming | Flat flange, tight radii, ID/OD control |
| Brackets & lock plates | Stamping, bending (wire-cut dies) | Burr-free edges, consistent geometry, strength |
| Hardened shims | Blanking → heat treatment → plating | Hardness, flatness, thickness tolerance |
| Mounting plates & enclosures | Blanking, stamping, forming | Flatness, no post-stamp deformation |
Press range 25 t to 350 t; heat treatment and plating coordinated with qualified partners; inspection reports available per lot.
Balford supplies these parts from a 12,000 m² plant in Zhuji, Zhejiang, forming them on presses from 25 t to 350 t.
Engineering & Quality Considerations
- Consistent crimping and seating geometry on ferrules and collars is controlled in the tool, so field assembly behaves the same from lot to lot.
- Fatigue-critical corners on brackets and lock plates are reviewed during DFM so bend radii and edge conditions match the load case.
- Surface protection: zinc, zinc-nickel and blackening are coordinated for industrial environments; coating thickness is verified on request.
- Machinery spares and low-volume parts can be produced from drawing or sample with documented inspection, including hardened shims and specialty blanks.
Frequently Asked Questions
Stamped and deep-drawn valve housings and ferrules, anti-vibration bushings and rings, brackets, lock plates, shims, mounting plates and drawn enclosures — in carbon steel, stainless steel, spring steel and aluminum.
Yes. Prototype tooling validates the part quickly; production then runs on progressive or dedicated tooling sized for the annual volume, with in-process inspection at defined intervals.
Yes. We can reverse-engineer a simple stamped part from a sample and confirm the drawing with you before tooling. This is how an obsolete or discontinued part is normally recovered: the original drawing is gone, or the supplier has stopped making the item, so the sample is measured, the geometry is rebuilt, and the drawing comes back to you for approval before any tool is cut. It applies to parts that fit our stamping and deep drawing processes — if a sample turns out to need a process we do not run, we say so rather than quoting it.
Zinc plating, zinc-nickel, blackening and passivation are coordinated with qualified partners; hardened and plated shims are produced with the heat-treatment route documented.
ISO 9001:2015 quality management with IATF 16949-aligned controls. FAI reports, material certificates and PPAP-aligned documentation are available on request.
Have a Drawing, Sample or 3D Model?
Send us your 2D drawing, sample or STEP/IGES model. We will review material, tolerances, forming requirements and production volume before quoting.